Armstrong A6206161 Guide d'installation télécharger pdf

CeraRoma Groutable Tile Installation

Installation Systems \ Vinyl Tile\CeraRoma Groutable Tile Installation

Subfloors:

Adhesive:

S-288

Installation

System:

CeraRoma™ Groutable Tile Installation

Pattern Match:

Seams:

Fittings:

Special Recommendations and Precautions:

General Information and Guidelines for CeraRoma™ Groutable Tile

CeraRoma™ Groutable Tile is designed to be installed as a grouted installation using a premixed

sanded acrylic grout having good flexural strength and adhesion properties. It may also be installed

without grout. The choice is yours. In either case, the floor is installed using Armstrong S-288

Flooring Adhesive.

If using grout, tiles should be laid with a grout joint spacing of 1/16" to 1/4" utilizing tile spacers

designed for this purpose. Because of the rounded edges, the appearance of the finished grout joint

will be 1/16" wider than the actual tile spacing.

Due to the floor's large format and increased thickness, care is required in handling and storage to

keep the product from becoming damaged or distorted. Always store the product on a flat surface.

Temperature control

and subfloor flatness are important in the prevention of raised or curled edges,

and performance of the grouted joints. Maintain the temperature of the room, subfloor, tile and

adhesive at a minimum of 65° F (18° C) and a maximum of 85° F (29° C) for 48 hours prior to

installation, during installation and 48 hours after installation. Maintain a minimum room temperature

of 55° F (13° C) thereafter.

CAUTION: Do not use high temperature heat sources to aid in cutting or making the tile conform to

irregularities in the substrate. Multi-layered engineered tile structures such as CeraRoma™ can warp

or curl after significant heating from sources such as hot plates and heat guns. Condition the room

and all flooring materials to the temperature guidelines stated above. If you must warm the tile,

always heat from the back and limit the temperature of the tile to warm conditions--less than 110° F

(43° C).

Suitable Substrates

All substrates listed below must be properly prepared and meet certain requirements. (Refer to

www.floorexpert.com for more details.)

Concrete (on all grade levels)

Approved suspended wood underlayments

Most single-layer, fully adhered, existing resilient floors on approved subfloors and

underlayments

Ceramic tile, terrazzo, marble

Polymeric poured (seamless) floors

Do not install over:

Particleboard, waferboard, OSB or single-layer STURD-I-FLOOR panels

Existing resilient tile floors that are on-grade or below-grade

Existing cushioned vinyl flooring

Carpet

Hardwood flooring that has been installed directly over concrete

1 2 3 4

Résumé du contenu

Page 1

CeraRoma Groutable Tile Installation Installation Systems \ Vinyl Tile\CeraRoma Groutable Tile Installation Subfloors: Adhesive: S-288 Installation

Page 2

Job Conditions/Preparation Substrates must be sound, dry, clean, smooth, and free from excessive moisture or alkali. Remove dirt, paint, varnish, w

Page 3

Layout: Before installing CeraRoma™ , plan the layout so tile joints fall at least 6" away from subfloor/underlayment joints. Do not install ove

Page 4

Grouting: Grouting may be done immediately. Grouting can also be completed the following day. A premixed sanded acrylic grout with good flexural st

Commentaires sur ces manuels

Pas de commentaire

Armstrong A6206161 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Non Armstrong A6206161. Armstrong A6206161 Installation Guide [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Non Armstrong A6206161